A brake pad is a consumable, and the aftermarket has always treated it as one. Pads and discs wear out because friction converts motion into heat, and the replacement cycle has been a dependable source of demand. Electrification changes the arithmetic: an electric or hybrid vehicle can slow down by running its motor backwards as a generator, recovering energy that would otherwise be burned off in the brakes. The friction brakes are still there, but they are used less.
The interesting question for the parts industry is not whether regenerative braking reduces wear. It is how much, under which conditions, and what the reduction does to the structure of demand. Measurement studies now give usable answers, and they are less uniform than the headline claim.
The mechanism: regen takes the easy stops
In a conventional vehicle, every deceleration is friction braking. In an electrified vehicle, the motor-generator can absorb braking energy and push it back into the battery, subject to limits: how much power the motor and inverter can handle, how much charge the battery can accept, and how the vehicle blends regenerative and friction braking.
The blending is the important detail. Regenerative braking is efficient at moderate, predictable decelerations. It becomes less able to absorb energy when the driver brakes hard, when the battery is full or cold, or when the required deceleration exceeds the motor's generating capability. At that point friction braking takes over. The wear question therefore depends as much on driving behaviour and vehicle calibration as on the presence of a battery.
What the measurements show
A modelling study across vehicle classes and driving styles estimated the effect of regenerative braking systems on brake-wear particulate emissions. It found that regenerative systems would reduce brake wear by between 64 and 95 percent, and that urban brake-wear emission factors for electric powertrains ranged from about 3.9 to 5.5 mg PM10 per kilometre and 1.5 to 2.1 mg PM2.5 per kilometre, an average reduction of about 68 percent in emission factors. The same study found that, within an electrified fleet, a subcompact vehicle required 38 to 68 percent less friction brake power than a heavier sport-utility vehicle, illustrating how vehicle mass and driving style interact with the regenerative system (Hicks, Green & Beevers, 2023).
Real-world measurements sharpen the picture. A plug-in hybrid instrumented on mountainous roads in Chongqing logged more than three thousand braking events classified as normal, adaptive-cruise-control or aggressive. Regenerative efficiency ranked about 64 percent in normal driving, 58 percent under adaptive cruise control and 53 percent in aggressive driving. More than 90 percent of the friction energy in aggressive driving occurred beyond the power limit of the regenerative system, and estimated brake-wear PM10 under aggressive driving was two to four times the normal level (Hu, Zheng, Chen, Li & Liu, 2025).
That result is important for anyone modelling aftermarket demand. It means the same vehicle can look like two different customers. A fleet driven smoothly may consume far fewer friction parts per year than a vehicle driven hard, even if both are the same model. Average wear is not a property of the car alone; it is a property of the car, the driver and the route.
Experimental work on brake-wear particles from battery-electric vehicles supports the general direction. One study built a dedicated measurement setup for an in-use battery electric vehicle, with a separate brake housing and filtered ventilation, and measured airborne brake-wear emissions on a chassis dynamometer across standard and real driving cycles, including an investigation of emission control through regenerative braking (Bondorf et al., 2023). Separate experimental work reported that regenerative braking effectively reduces the formation of brake-wear particles (Zhang et al., 2023). The exact percentage varies with cycle and vehicle, but the direction is consistent across laboratory and simulation studies.
Pad life is now a modelling problem
If friction braking is reduced, pad service life should extend, and field experience in electrified fleets generally reflects that. A study of brake pad life in regenerative-braking-intensive applications noted that regenerative braking undoubtedly extends pad service life in most cases, and set out to estimate the effect more precisely. It adapted validated field wear models for regenerative vehicles, including models for battery charge acceptance, state of charge, electric drive characteristics and customer charging habits, and used them in case studies (Antanaitis & Robere, 2022).
Two industry consequences follow from that work. First, dedicated electric architectures give designers the opportunity to optimise the friction brake for lower duty: smaller, lighter and differently specified hardware. Second, the emergence of driver-facing brake-pad-life monitoring changes the service relationship: a workshop no longer waits for a squeal or a dashboard light at a fixed interval, because the vehicle can estimate remaining pad life from actual use.
For the parts industry, this is a subtle but real shift. Demand becomes less predictable at the vehicle level and more dependent on duty cycle, and the service interval becomes software-mediated. A catalogue built around fixed replacement intervals is optimised for a world that is slowly disappearing.
What regenerative braking does not change
The friction-brake market is not going away, and the reasons matter more than the headline wear reduction.
First, friction brakes remain the safety system. Regenerative braking is limited by battery state, temperature and power electronics, so the friction circuit must remain capable of stopping the vehicle. The hardware stays, even if it is used less.
Second, not all wear is friction wear. Brake components degrade through corrosion, seal ageing, fluid absorption and contamination, and pad slide and caliper mechanisms can seize when they are used infrequently. A vehicle that brakes rarely can still need brake work, and a brake system that sits idle is not automatically a reliable one.
Third, mass matters. Electric vehicles are generally heavier than comparable internal-combustion vehicles because of the battery. The modelling study above found that heavier vehicles require more friction brake power within an electrified fleet, which partially offsets the regenerative benefit (Hicks, Green & Beevers, 2023).
Fourth, aggressive driving and high payloads push energy demand beyond what regeneration can absorb, as the Chongqing measurements showed. Commercial and heavy-duty use is therefore less protected from friction wear than light-duty commuting.
The architecture shift matters as much as the wear rate
The way braking is actuated is changing at the same time as the wear rate. Electro-hydraulic braking systems combine the electric booster and wheel-cylinder pressure control in one unit, and a review of one-box electro-hydraulic systems describes functions that include service braking, pedal-feel simulation, brake decoupling, failure backup and active braking (Zhao et al., 2024). A survey of brake-by-wire systems for intelligent connected electric vehicles describes the technology as central to braking performance and energy-recovery efficiency, while noting that technical problems remain to be solved (Meng, Yang, Liu & Wang, 2020).
For the aftermarket, the consequence is that a growing share of brake hardware is not the familiar vacuum-booster-and-master-cylinder arrangement. It is an integrated, electronically controlled assembly, and the serviceable parts inside it are different: pressure sensors, motors, control modules, seals and hydraulic units rather than only diaphragms and valves. The wear data tell us that friction consumables will grow more slowly per vehicle-mile. The architecture data tell us that the value in the system is migrating toward the controlled assembly.
Remanufacturing and the composition effect
Electrification does not only change how much wear occurs; it changes what can be remanufactured. A study combining theory with industry-expert validation examined the effects of electrification on automotive remanufacturing and found that the shift from internal-combustion to battery-electric drive trains changes core availability, the economics of remanufacturing and the competences required, creating both challenges and opportunities for the remanufacturing industry (Casper & Sundin, 2020).
This is the composition effect that a simple "EVs need fewer brake jobs" story misses. The total number of friction parts consumed per vehicle may fall, but the mix of parts, the technical documentation required to service them, and the qualification of the workshops doing the work all shift. A supplier whose catalogue is deep in mechanical brake assemblies has to decide how much of its future is in those assemblies and how much is in the electronic and hydraulic units that surround them.
An industry outlook, not a demand collapse
Putting the evidence together gives a more useful outlook than either the optimistic or the pessimistic version.
Demand for friction consumables per vehicle-mile is structurally lower in electrified fleets, and the reduction is large under smooth driving: modelling suggests most friction braking can be displaced, and real-world measurements show regenerative efficiency above 60 percent in normal driving. But the reduction is uneven, because aggressive driving and heavy vehicles push energy demand beyond regenerative limits, and because corrosion and seal ageing generate brake work that has nothing to do with pad thickness.
At the same time, the vehicle parc is still growing in many markets, the internal-combustion installed base will remain large for years, and electric vehicles are heavier. Those factors offset part of the per-vehicle reduction. The result is not a collapse in brake-parts demand; it is a slower growth rate for friction consumables, a rising share of value in controlled assemblies, and a service market increasingly mediated by software and data.
For a parts business, that argues for breadth and technical depth rather than a single-product bet: a catalogue that spans both the conventional vacuum and hydraulic assemblies and the newer electro-hydraulic units, with the documentation to match part numbers to vehicle architectures. The wear data are unambiguous about the direction. The competitive question is how quickly the mix moves, and which suppliers are positioned to move with it.
Where these parts sit in the catalogue
The conventional assemblies that still dominate the parc are listed by part number and application in our vacuum brake booster, hydraulic brake booster and hydro-boost and ABS pump categories, alongside the friction-side parts in the brake caliper and brake master cylinder categories.
References
- Hicks, W., Green, D. C., & Beevers, S. (2023). Quantifying the change of brake wear particulate matter emissions through powertrain electrification in passenger vehicles. Environmental Pollution, 336, 122400. https://doi.org/10.1016/j.envpol.2023.122400
- Hu, R., Zheng, J., Chen, X., Li, L., & Liu, Y. (2025). Driving behavior shapes PHEV brake energy and brake wear particle emissions. Transportation Research Part D: Transport and Environment, 150, 105087. https://doi.org/10.1016/j.trd.2025.105087
- Bondorf, L., Köhler, L., Grein, T., Epple, F., Philipps, F., Aigner, M., & Schripp, T. (2023). Airborne Brake Wear Emissions from a Battery Electric Vehicle. Atmosphere, 14(3), 488. https://doi.org/10.3390/atmos14030488
- Zhang, Q., Yin, J., Fang, T., Guo, Q., Sun, J., Peng, J., Zhong, C., Wu, L., & Mao, H. (2023). Regenerative braking system effectively reduces the formation of brake wear particles. Journal of Hazardous Materials, 465, 133350. https://doi.org/10.1016/j.jhazmat.2023.133350
- Antanaitis, D., & Robere, M. (2022). Estimating Brake Pad Life in Regenerative Braking Intensive Vehicle Applications. SAE International Journal of Advances and Current Practices in Mobility, 5(4), 1424-1437. https://doi.org/10.4271/2022-01-1161
- Zhao, X., Xiong, L., Zhuo, G., Tian, W., Li, J., Shu, Q., Zhao, X., & Xu, G. (2024). A Review of One-Box Electro-Hydraulic Braking System: Architecture, Control, and Application. Sustainability, 16(3), 1049. https://doi.org/10.3390/su16031049
- Meng, B., Yang, F., Liu, J., & Wang, Y. (2020). A Survey of Brake-by-Wire System for Intelligent Connected Electric Vehicles. IEEE Access, 8, 225424-225436. https://doi.org/10.1109/ACCESS.2020.3040184
- Casper, R., & Sundin, E. (2020). Electrification in the automotive industry: effects in remanufacturing. Journal of Remanufacturing, 11(2), 121-136. https://doi.org/10.1007/s13243-020-00094-8
